Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
This article below on the subject of Tools You Need to Install a New Bathtub is exceptionally entertaining. You should check this stuff out.
Mounting a bathtub isn't exactly rocket science, yet it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately tough project. If the old tub is conveniently obtainable, the task can relocate easily; if you have to open up a wall surface to get rid of the old tub and also position the new bath tub, the task is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to leave the old bathtub and embeded in the new one. Ensure you have actually qualified yourself for the job as well as fit attempting it. Instead of hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This write-up will certainly assist you mount a brand-new tub in your shower room if you have already acquired a new bathtub as well as don't need to transform the plan of your previous water supply pipelines.
Your devices and also product list should consist of the following:
Planning for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if needed) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its final placement.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water supply. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome as a result of the limited access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, put the bath tub in the needed position. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level and also changing the feet on the tub until the spirit level checks out degree.
To mount taps, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipe by making a compression join; after that do the same for the other tap.
Activate the supply of water and also check all joints and new pipework for leakages and tighten them if necessary. Load the bath tub and also check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's instruction manual. Tiling and securing around the tub ought to wait up until the bathtub has actually been utilized at least once as this will certainly settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washers are in place between the faucet and the sink. Protect the faucet in position with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a rigid seal, triggering the water to permeate the wall in between the bath as well as the tiling, leading to issues with wetness and also possible leaks to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is suggested to fit the floor tiles utilizing waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that article about Tools You Need to Install a New Bathtub from an associate on another site. Be sure to take the time to promote this content if you appreciated it. I truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Get answers now! Report this page